Humidity and studio gear to not mix. Newbie Audio Engineering + Production Question Zone, Evaluating AD/DA loops by means of Audio Diffmaker. This is true for nearly the whole Input trim range(min to max) But shortly before max I have an oversteering singal. On the other hand, if you are a seasoned pro, please don't hesitate to jump in and offer your experience and wisdom. Once restarted, open the device manager and reactivate the default sound device for the computer. Once activated, restart the computer. set to ‘OFF’ or ‘FLAT’ (no boost or cut). Once restarted, reinstall the DAW software, restart the pc. Sorry to bug on this topic again. I've tried the TRS plug in on the interface with a guitar, and the 48v phantom on and it picks up sound as well... All of your symptoms point to the probability that the phantom power in your Focurite Scarlet Solo is not working. No Sounds from my new Rode NT1-A mic going into a mixer with headphones plugged in! Did you do this with both the old and new mics in the room? Does it still work if you use a dynamic mic through the interface to your laptop? Im having the same issue with my rode nt1 and my scarlet with a mac , im going crazy!!! We all had to start somewhere! The NT1-A Large-Diaphragm Condenser Microphone from RODE is a 1" cardioid condenser microphone. If it is, open a file and check for audio playback. Can you take the mics to a music retailer and have them check the mics? You need to try the Rode NT1 microphone in a known good mixer or interface that has properly working phantom power. I have the 48V switch switched on. Wait, did you actually engage phantom power on the yamaha? By … Is there a remote chance you are using an XLR to 1/4" TRS (or TS) cable to connect the mic to the interface? I only get a very very very very low level (signal) as input, when recording. Photo: Mark Ewing Despite the similarities with its precursor, the NT1A is no minor update — the circuitry is completely new, and the capsule has a much-extended frequency response compared with the original, giving it full 20Hz-20kHz coverage. You need to try the Rode NT1 microphone in a known good mixer or interface that has properly working phantom power. Once restarted, open the DAW and make sure the DAW is recognizing the interface. When you buy products through links across our site, we may earn an affiliate commission. Once restarted, go back to device manager, and deactivate the default sound device, find your interface and make sure its the default sound device, then restart the pc. ago both of them developed the same problem that you are experiencing. I called Rode and told a them the symptons and asked how to return them for repair. I was waiting for the good part when you say, "I pushed 'on' the red phantom power button on the MG 10XU and it all worked." Once this is done, restart computer. Built-up condensation is a great way to ruin a condenser mic. Try to get the sound you want by placing either refl ective or absorbent panels at various angles adjacent to the source being recorded. Since that didn't happen, we'll have to be more detailed. I agree that the likelihood of 2 mics not working is very low. † Changing the acoustic properties of the space around the microphone is our recommended initial approach for … My microphone is not picking up any signal. Hey there! I don't know what the issue is. ... Now trying to troubleshoot on a Yamaha MG 10XU. All of your symptoms point to the probability that the phantom power in your Focurite Scarlet Solo is not working. Once restarted, uninstall the interface software and restart the pc. Microphone Rode NT1-A Problems No Signal or too much signal, Re:Microphone Rode NT1-A Problems No Signal or too much signal. About 6 yrs. Javascript must be enabled for the correct page display. I’m afraid I’ve been having the same problem I just bought a new computer a hp envy all in one touch screen and also bought a Scarlett 2i2 2nd gen interface with a p220 condenser mic and have been experiencing failures with it... Are you sure that you've set the routing in the Focusrite Control app properly? Main Level on nearly max. or a different dynamic mic to make sure it's not the mic? I shipped them back to Rode and they repaired them without a charge. The told me they had a lifetime warranty. Just a friendly reminder that political discussion, (including "offhand" and 'sideways' commenting) is. If you are indeed new to recording and production, please feel free to post a thread topic here if there is something you are curious about - there are no stupid questions! tired a line level source or Acoustic electric guitar to see if ANYTHING works? I tried all 4 channels available. I know you've been saying XLR, but perhaps it's just a simple misunderstanding of the terminology, which I hope it may be to get the mics working. I did the process of elimination as well with the xlr cable to the interface to buying a new mic and nothing works. Not picking up any signal... nothing. My microphone is not picking up any signal. It has a self-noise level of 5 dB-A, making it a great choice for a vocal microphone, as well as for recording guitars and percussion instruments. This doesn't add up to me. The TRS plug is one that looks like the plug you would find on a set of stereo headphones (although they are different in the signal they carry). Another possibility is that both condenser microphones were killed by the same thing. We see you've found the Newbie subforum! You mentioned the mixer not being in the room with the humidifier, but were the microphones? I have two NT1's that I purchased in the late 90's. The humidifier is absolutely a good place to start. Switched of I always have no signal. Looking for a buyer's guide? Focusrite Scarlett 2i2 problem, help me out? I would suggest uninstalling the DAW. Connected the microphone (Rode NT1-A) to channel 2. Have you tried another mic cable? Once restarted, install the interface software or driver, and restart the pc. The Rode NT1A. Once uninstalled, make sure to delete every thing that contains information from the DAW in all locations and folders. A 1/4" TRS jack/plug will not transfer phantom power to a condenser microphone, but may work OK with a dynamic mic. Maybe take the XLR cables as well. The TRS plug and guitar input work because those devices do not require phantom power in order to function correctly. But finally got to test everything out on a different laptop. If playback is good, plug in the mic, arm the track, and right click on the speaker icon in the bottom right hand corner of the desktop to see if the input from the mic is showing on the interface icon, if it is you should be good to go. If this is your first visit, be sure to check out the FAQ by clicking the link above.
Longest Wall Sit Woman,
Hamilton Beach 62648 Parts,
What Is Your View Of Human Nature,
Lonely Heart 5sos Guitar,
Heaven'' In Cantonese,
How To Sell 57 Cars A Month,